oduct Description

• Flat frequency response
• Low conversion loss
• No bias or tuning adjustments
• 100 mW safe input level

The Keysight 11970A waveguide mixer is a general-purpose harmonic mixer employing a dual-diode design to achieve flat frequency response and low conversion loss. These are achieved without external dc bias or tuning stubs. Manual operation and computer-controlled hardware operation are simplified because mixer bias and tuning adjustment are not required.

The 11970A extends the frequency range of the Keysight N9030A PXA high-performance signal analyzer to the A-Band (26.5 to 40 GHz). It is also fully compatible with other Keysight spectrum analyzers including: the E4440A/46A/48A PSA (with Option AYZ), the E4407B ESA-E (with Option AYZ), the 856xEC, the 8566B (with a preamplifier), and the 7000 modular analyzer (with the 70907A/B external mixer interface module).

An external diplexer is required to connect the 11970A with the N9030A PXA (with Option EXM). The recommended diplexer can be purchased from Keysight as model number N9029AE13 or from OML, Inc as model number DLP.313B.

Contact your Keysight sales representative for ordering the N9029AE13.

Embedded smart features

• Automatic amplitude correction and transfer of conversion loss data through USB plug and play features
• Automatic LO amplitude adjustment to compensate the cables loss (up to 3 m or 10 dB loss)
• Automatic detect mixer model/serial number when used with N9030A PXA, N9020A MXA, and N9010A EXA signal analyzers
    o  Automatic setting of the default frequency range and LO harmonic numbers
    o  Automatic LO alignment at start up
    o  Automatic run calibration when time and temperature changes

Improved DANL and TOI

• Excellent conversion loss of 25 dB maximum and excellent amplitude accuracy

The Keysight M1970W 75 to 110 GHz waveguide harmonic mixer is an un-preselected mixer that will extend the operating frequency range of N9030A PXA, N9020A MXA, and N9010A EXA signal analyzers up to 110 GHz. Smart features are embedded to help you to greatly simplify your overall test setup and improve your DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.

Embedded smart features

• Automatic amplitude correction and transfer of conversion loss data through USB plug and play features
• Automatic LO amplitude adjustment to compensate the cables loss (up to 3 m or 10 dB loss)

• Automatic detect mixer model/serial number when used with N9030A PXA, N9020A MXA, and N9010A EXA signal analyzers
     o  Automatic setting of the default frequency range and LO harmonic numbers
     o  Automatic LO alignment at start up 
     o  Automatic run calibration when time and temperature changes 

Improved DANL and TOI

• Excellent conversion loss of 23 dB maximum and excellent amplitude accuracy

The Keysight M1970V 50 to 75/80 GHz waveguide harmonic mixer is an un-preselected mixer that will extend the operating frequency range of the N9030A PXA, N9020A MXA, and N9010A EXA signal analyzers up to 80 GHz. Smart features are embedded to help you to greatly simplify your overall test setup and improve your DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.

Embedded smart features

• Automatic amplitude correction and transfer of conversion loss data through USB plug and play features
• Automatic LO amplitude adjustment to compensate for cable loss (up to 3 m or 10 dB loss)
• Automatic detect mixer model/serial number when used with N9030A PXA, N9020A MXA, and N9010A EXA signal analyzer
     o  Automatic setting of the default frequency range and LO harmonic numbers
     o  Automatic LO alignment at start up      
     o  Automatic run calibration when time and temperature changes

Improved DANL and TOI

• Excellent conversion loss of 27 dB maximum and excellent amplitude accuracy

The Keysight M1970E 60 to 90 GHz waveguide harmonic mixer is an un-preselected mixer that will extend the operating frequency range of the N9030A PXA, N9020A MXA, and N9010A EXA signal analyzers up to 90 GHz. Smart features are embedded to help you to greatly simplify your overall test setup and improve the DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.

 Embedded smart features:

• Automatic amplitude correction and transfer of conversion loss data through USB plug and play features
• Automatic LO amplitude adjustment to compensate for cable loss (up to 3 m or 10 dB loss)
• Vector correction data include magnitude and phase improving EVM measurement
• Automatic detect mixer model/serial number when used with N9040B UXA, N9030A PXA, N9020A MXA, and N9010A EXA signal analyzer

               - Automatic setting of the default frequency range and LO harmonic numbers

               - Automatic LO alignment at start up

               - Automatic run calibration when time and temperature changes

Improved DANL and TOI:

• Excellent conversion loss of 27 dB maximum and excellent amplitude accuracy

Keysight M1971E 55/60 to 90 GHz waveguide harmonic mixers is an un-preselected mixer provides a complete solution for wideband millimeter-wave signal analysis of more than 2 GHz with X-Series signal analyzers. Smart features are embedded to help you to greatly simplify your overall test setup and improve the DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.

M1971E

Option 001 60 to 90 GHz Waveguide harmonic mixer
Option 003 55 to 90 GHz Waveguide harmonic mixer

• 35 MHz bandwidth
• 1:1 attenuation ratio
• 39 pF input capacitance
• 1 MΩ input resistance (when terminated into 1 MΩ scope input)
• Max input voltage: 30 Vrms mains isolated, 60 Vdc

The N2870A passive probe offers DC to 35 MHz and 1:1 attenuation factor, making this probe ideal for low-level signal measurements.

Probe densely populated IC components or surface-mount devices used in high-speed digital applications with a compact 2.5-mm probe head diameter, low input capacitance, and various fine-pitch probe tip accessories.

The sharp, spring-loaded probe tip keeps the probe from slipping off the device under test. Insulating IC caps helps you center small probe tip on the IC lead, so it doesn't short adjacent leads. Reduce ground inductance while easily accessing the ground with our standard flat blade ground connector and self-adhesive copper ground pad. Optional probe tip accessories provide specialized capabilities for demanding applications.

Compatible with Keysight InfiniiVision and Infiniium Series oscilloscopes with 1 MΩ input.

To see all probes in the N287xA Series, ranging from 35 MHz to 1.5 GHz,  see Related Products on the Options & Accessories tab.

• Risetime (calculated): < 17.5 ns
• Input resistance: 1 MOhm; (when terminated into 1 MOhm;)
• Designed for optimal performance with your Keysight InfiniiVision 5000, 6000 or 7000 Series and 54620 Series oscilloscope
• Input capacitance: 70 pF (approximate)

The Keysight 10070D 20 MHz passive probe is a great choice if you are looking for high quality at a very reasonable price. This general purpose probe is designed specifically to give you optimal performance with your 5000, 6000, 7000 Series, 54620 Series and 9000 Series oscilloscopes. Rugged enough for general-purpose measurements, the 10070D features a durable cable and a solid stainless-steel probe body encased with a hard, fracture-resistant plastic.

• General-purpose retractable hook tip - hooks onto wires and test points for hands-free probing
• Ground bayonet - provides short, flexible ground lead for high-frequency measurements
• General purpose alligator clip ground lead - allows for versatile grounding
• Color tags (2 tags in each color: orange, white, blue and green) - by placing tags at both ends of the probe cable, you can quickly identify your probes

The 10070D replaces the 10070C, discontinued in June 2011. The old and new replacements are 100% form, fit, function and price equivalent to the products they replace.

• 700 MHz bandwidth
• 10:1 attenuation ratio
• 9.5 pF input capacitance
• 10 MΩ input resistance (when terminated into 1 MΩ scope input)
• 400 V CAT I and 300 V CAT II maximum input voltage
• Scope compensation range: 10 – 25 pF
   

The N2894A passive probe offers DC to 700 MHz and 10:1 attenuation factor to address a wide range of measurement needs.

Compact 2.5-mm probe head diameter, low input capacitance, and various fine-pitch probe tip accessories make the Keysight N2894A Series passive probes ideal for probing densely populated IC components or surface-mount devices used in today’s high-speed digital applications.

The sharp probe tip is spring loaded to help engineers keep the probe from slipping off the device under test. Insulating IC caps keep the small probe tip centered on the IC lead and prevent it from shorting adjacent leads. Standard flat blade ground connector and self-adhesive copper ground pad help reduce ground inductance while offering easy ground access. Optional probe tip accessories provide specialized capabilities for demanding applications.

This probe is compatible with Keysight InfiniiVision 4000 X Series oscilloscopes with 1 MΩ input. The N2894A provides 700 MHz system bandwidth when used in conjunction with the 4000 X-Series 1 GHz/1.5 GHz models.

• 500 MHz bandwidth
• 20:1 attenuation ratio
• 5.6 pF input capacitance
• 20 MΩ input resistance (when terminated into 1 MΩ scope input)
• 400 V CAT I and 300 V CAT II maximum input voltage
• scope compensation range: 10 – 25 pF

• 500 MHz bandwidth
• 10:1 attenuation ratio
• 9.5 pF input capacitance
• 10 MΩ input resistance (when terminated into 1 MΩ scope input)
• 400 V CAT I and 300 V CAT II maximum input voltage
• Scope compensation range: 10 – 25 pF

The N2873A passive probe offers DC to 500 MHz and 10:1 attenuation factor to address a wide range of measurement needs.

Compact 2.5-mm probe head diameter, low input capacitance, and various fine-pitch probe tip accessories make the Keysight N2870A Series passive probes ideal for probing densely populated IC components or surface-mount devices used in today’s high-speed digital applications.

The sharp probe tip is spring loaded to help engineers keep the probe from slipping off the device under test. Insulating IC caps keep the small probe tip centered on the IC lead and keep it from shorting adjacent leads. Standard flat blade ground connector and self-adhesive copper ground pad help reduce ground inductance while offering easy ground access. Optional probe tip accessories provide specialized capabilities for demanding applications.

Compatible with Keysight InfiniiVision and Infiniium Series oscilloscopes with 1 MΩ input. This probe ships with Keysight’s 9000 Series Infiniium oscilloscope.

• Bandwidth: 500 MHz
• System risetime (calculated): < 700 ps
• Attenuation Ratio: 10:1
• Input resistance: 2.2 MΩ (when terminated into 1 MOhm)

The Keysight 10073D passive probe is our most rugged 500 MHz probe. With a 10:1 attenuation ratio and high 2.2 M ohm input impedance, it is ideal as a general purpose, high bandwidth passive probe for the Keysight 300 MHz - 1 GHz 6000 series, 7000, 8000 and 9000 Series oscilloscopes. The probe identification feature automatically configures the oscilloscope for the probe attenuation.

The following accessories are included: retractable hook tip; orange, white, blue and green identification tags; ground bayonet, IC probing tip, adjustment tool and an alligator clip ground lead.

• Bandwidth: 500 MHz
• System rise time (calculated): <700 ps
• Attenuation Ratio: 10:1
• Input resistance: 2.2 MΩ (when terminated into 1 MOhm)
• Input capacitance: ~12 pF
• Maximum input (dc + peak ac): 500 V CAT I (mains isolated) 300 V CAT II (post receptacle mains)
• Compensation range: 6 - 15 pF

• Bandwidth DC to 500 MHz
• Cable length 1.2 m
• Rise time 700 ps
• Attenuation ratio 10:1
• Input resistance 10 MΩ (when terminated into 1 MΩ)
• Maximum input 300 V RMS (or >400Vpk) CAT I and CAT II
• Compatible with Keysight InfiniiVision and Infiniium Series oscilloscopes with 1 MΩ input
• Probe ID
   

The Keysight N2843A low-cost passive probe provides a 10:1 attenuation and features a high input resistance of 10 MΩ. The probe can be adjusted for low-frequency compensation and high-frequency compensation.

For the best measurements you should compensate your probe to match its characteristics to the oscilloscope.

The N2843A is a replacement of the N2890A. The old and new replacements are 100% form, fit, function, and price equivalent to the products they replace.

• Bandwidth: 400 MHz
• Attenuation ratio: 10:1
• Input impedance (@DC): 10 Mohm//15.5 pF
• Operating temp range: -40 to +85 deg C
• Operating humidity range: <90% at 40 degC
• Cable Length: 2 m
• Max input range: 1 kV CAT II, 600V CAT III

Many environmental test engineers today are using standard-temperature probes in extreme temperature condition, which causes physical damage to the probe. Another common practice among environmental test engineers is to simply attach long wires at the end of their probes, which significantly degrades measurement performance due to excessive inductance and reduced bandwidth. Keysight addresses this issue with the N7007A single-end passive probe.

The N7007A is a 2-meter long, 10:1 passive probe with an input impedance of 10 MΩ and 400 MHz bandwidth. This probe can withstand temperatures ranging from -40 to +85 °C.

• 350 MHz bandwidth
• 10:1 attenuation ratio
• 9.5 pF input capacitance
• 10 MΩ input resistance (when terminated into 1 MΩ scope input)
• 400 V CAT I and 300 V CAT II maximum input voltage
• Scope compensation range: 10 – 25 pF

The N2872A passive probe offers DC to 350 MHz and 10:1 attenuation factor to address a wide range of measurement needs.

Compact 2.5-mm probe head diameter, low input capacitance, and various fine-pitch probe tip accessories make the Keysight N2870A Series passive probes ideal for probing densely populated IC components or surface-mount devices used in today’s high-speed digital applications.

The sharp probe tip is spring loaded to help engineers keep the probe from slipping off the device under test. Insulating IC caps keep the small probe tip centered on the IC lead and keep it from shorting adjacent leads. Standard flat blade ground connector and self-adhesive copper ground pad help reduce ground inductance while offering easy ground access. Optional probe tip accessories provide specialized capabilities for demanding applications.

Compatible with Keysight InfiniiVision and Infiniium Series oscilloscopes with 1 MΩ input. Recommended for oscilloscopes with <350 MHz bandwidth.

• DC to 350 MHz bandwidth
• 2 m cable 
• 1 ns rise time 
• 10:1 attenuation ratio
• 10 MΩ input resistance when terminated into 1 MΩ
• maximum input 300 V RMS (or >400 Vpk) CAT I and CAT II
• compatible with Keysight InfiniiVision and Infiniium Series oscilloscopes with 1 MΩ input
• probe ID

The Keysight N2853A low-cost passive probe provides a 10:1 attenuation and features a high-input resistance of 10 MΩ. The probe can be adjusted for low-frequency compensation and high-frequency compensation.

For the best measurements you should compensate your probe to match its characteristics to the oscilloscope.

• Bandwidth DC to 300 MHz
• Cable length 1.2 m
• Rise time 1.16 ns
• Attenuation ratio 10:1
• Input resistance 10 MΩ (when terminated into 1 MΩ)
• Maximum input 300 V RMS (or >400Vpk) CAT I and CAT II
• Compatible with Keysight InfiniiVision and Infiniium Series oscilloscopes with 1 MΩ input
• Probe ID

The Keysight N2842A low-cost passive probe provides a 10:1 attenuation and features a high input resistance of 10 MΩ. The probe can be adjusted for low-frequency compensation and high-frequency compensation.

For the best measurements you should compensate your probe to match its characteristics to the oscilloscope.

The N2842A is a replacement of the N2863B. The old and new replacements are 100% form, fit, function, and price equivalent to the products they replace.

• 200 MHz bandwidth
• 10:1 attenuation ratio
• 9.5 pF input capacitance
• 10 MΩ input resistance (when terminated into 1 MΩ scope input)
• 400 V CAT I and 300 V CAT II maximum input voltage
• Scope compensation range: 10 – 25 pF

The N2871A passive probe offers DC to 200 MHz and 10:1 attenuation factor to address a wide range of measurement needs.

Compact 2.5-mm probe head diameter, low input capacitance, and various fine-pitch probe tip accessories make the Keysight N2870A Series passive probes ideal for probing densely populated IC components or surface-mount devices used in today’s high-speed digital applications.

The sharp probe tip is spring loaded to help engineers keep the probe from slipping off the device under test. Insulating IC caps keep the small probe tip centered on the IC lead and keep it from shorting adjacent leads.

Standard flat blade ground connector and self-adhesive copper ground pad help reduce ground inductance while offering easy ground access. Optional probe tip accessories provide specialized capabilities for demanding applications.

Compatible with Keysight InfiniiVision and Infiniium Series oscilloscopes with 1 MΩ input. Recommended for oscilloscopes with <200 MHz bandwidth.

• Bandwidth DC to 150 MHz
• Cable length 1.2 m
• Rise time 2.33 ns
• Attenuation ratio 10:1
• Input resistance 10 MΩ (when terminated into 1 MΩ)
• Maximum input 300 V RMS (or >400Vpk) CAT I and CAT II
• Compatible with Keysight InfiniiVision and Infiniium Series oscilloscopes with 1 MΩ input
• Probe ID

The Keysight N2841A low-cost passive probe provides a 10:1 attenuation and features a high input resistance of 10 MΩ. The probe can be adjusted for low-frequency compensation and high-frequency compensation.

For the best measurements you should compensate your probe to match its characteristics to the oscilloscope.

The N2841A is a replacement of the N2862B. The old and new replacements are 100% form, fit, function, and price equivalent to the products they replace.

• Risetime (calculated): <2.33 ns
• Input resistance: 10 MOhm; (when terminated into 1 MOhm;)
• Input capacitance: 15 pF (approximate)
• Mains isolated: 500 V CAT I
• Post receptacle mains: 400 V CAT II
• Compensation range: 9-17 pF

The Keysight 10074D 150 MHz passive probe is a great choice if you are looking for high quality at a very reasonable price. This general-purpose probe gives you optimal performance with your 6000 Series 100 MHz models and 54620 Series oscilloscopes. Ruggedized for general-purpose measurements, the 10074C features a durable cable and a solid-stainless steel probe body encased with a hard, fracture-resistant plastic.

• General-purpose retractable hook tip - hooks onto wires and test points for hands-free probing
• Ground bayonet - provides short, flexible ground lead for high-frequency measurements
• General purpose alligator clip ground lead - allows for versatile grounding
• Color tags (2 tags in each color: orange, white, blue and green) - by placing tags at both ends of the probe cable, you can quickly identify your probes

• Bandwidth DC to 50 MHz
• Cable length 1.2 m
• Rise time 7 ns
• Attenuation ratio 10:1
• Input resistance 10 MΩ (when terminated into 1 MΩ)
• Maximum input 300 V RMS (or >400Vpk) CAT I and CAT II
• Compatible with Keysight InfiniiVision and Infiniium Series oscilloscopes with 1 MΩ input 

The Keysight N2840A low-cost passive probe provides a 10:1 attenuation and features a high input resistance of 10 MΩ. The probe can be adjusted for low-frequency compensation and high-frequency compensation.

For the best measurements you should compensate your probe to match its characteristics to the oscilloscope.

• For use only with Keysight BGA interposers that include RC tip network for U4164A logic analyzers.
• Zero Ω (requires BGA interposer with RC network for U4164A designed into the BGA interposer).
• Standard Soft Touch Pro footprint.
• Direct connect into U4164A logic analyzer.
• Each W6602A LPDDR4 200-ball BGA interposer requires two U4207A Zero Ω, 34-channel, Soft Touch Pro, single-ended, 4 x 160-pin direct connect probes.
   

The Keysight U4207A zero Ω direct connect probes are used to connect a W6602A to two U4164A analyzer modules. Two U4207A are required for each W6602A LPDDR4 rigid BGA interposer.

• Low noise: 1.3:1 attenuation ratio probe adds only 30% to the baseline noise of the oscilloscope it is attached to
• Large offset range: Has a large +/-15.25 V offset range, enabling users to set their oscilloscope at maximum sensitivity and have the signal centered on the screen
• Low DC loading: 50 kΩ DC input impedance will not significantly load DC power rails
• Large active signal range: Has a +/-600 mV active signal range in addition to its large offset range so users can measure large transitions of their power rails
• High bandwidth: 6 GHz bandwidth makes it very useful for finding high-speed transients that can have detrimental effects on clocks and digital data

The N7024A power rail probe is for users making power integrity measurements that need mV sensitivity when measuring noise, ripple and transients on their DC power rails. The probe is designed for measuring periodic and random disturbances (PARD), static and dynamic load response, programmable power rail response, and similar power integrity measurements. Many of today’s products have tighter tolerances on their DC power rails than the previous generations of these products, and the N7024A power rail probe is designed to help users ensure their products meet these tighter tolerances.

The N7024A power rail probe can be used with the Keysight Infiniium S, 9000, 90000A, 90000X, V, Z and UXR <=33 GHz Series oscilloscopes. Note that Infiniium scope software ver 6.50.00906 or higher is needed to operate the N7024A on Infiniium 9000 or 90000A scope.

Learn more about Oscilloscope Single-Ended Active Probes

• Smaller than half the size of existing solder-in probe heads
• Flex printed circuit to make it flat and flexible
• 25 GHz bandwidth when used with MX0023A and 12 GHz bandwidth when used with 1169B
• Excellent probe loading – 0.17 pF
• Reusable
• Comes with 5 probe heads, 1 bullet adapter and 1 4-mil wire spool (opt 001)
• Compatible with InfiniiMax I/II probe amps
• Operating temperature characteristics
  o -55°C dwell, 1000 hours minimum
  o +150°C dwell, 1000 hours minimum
  o -55°C to 150°C cycles, 1000 cycles minimum per JEDEC JESD22-A104 revision E

The MX0100A is the smallest and highest performance solder-in probe head on the market, optimized for probing modern high-speed devices. The micro probe head is a micro solder-in head for use with Keysight InfiniiMax I/II and RC probe amplifiers designed to access small geometry target devices. The probe head is made out of flex printed circuit making it light, flexible, small, and yet highly usable and reusable. The solderable lead wires of the MX0100A ensure a secure connection to the DUT. The 4-mil diameter lead wires can be adjusted to accommodate targets from 0 mm to 7 mm apart.

For extended temperature testing, the MX0100A supports extreme operating temperature of -55 °C to +150 °C per JEDEC JESD22-A104 revision E, making it ideal for testing electronics circuits and devices in environmental chambers.